Skip to content

Create a request from the signing authority rules

If your company has signing authority rules, you do not have to find out yourself who approves a purchase order or a contract. You choose what it is about and enter the amount. actaSIGN proposes the steps and people and fills the workflow with them.

  1. In the first step, upload the document, and in the Recipients step choose Other people. Under Choose a Starting Point, click the From the rules tab.
  2. On the left, choose the request type, e.g. “Purchase order”. The badge on the right of the card shows the required signature: QES, AES, SES or Internal approval.
  3. Fill in the Details of the request. The amount (with *) is required; depending on the request type, fields such as currency, counterparty, cost centre or yes/no questions are added (e.g. “Abroad”).
  4. On the right, the Proposed workflow box appears as soon as the amount is entered. It changes while you type.
  5. Click Next. actaSIGN takes the request type, details and workflow over into the request.

Above the steps it says which version of the rules was used and the amount that counts, in CHF (foreign currencies are converted). Each step is named after its task, e.g. Approval, Approval and signature or Extra approval, and names the people with their role. If someone stands in for an absent person, “for …” follows the name.

Below, actaSIGN names special points, e.g.:

  • An extra condition applies (for example personal data or abroad).
  • Splitting: together with earlier requests to the same counterparty, the higher tier applies.
  • No approval in one’s own matter: you yourself never count for your own approval; the approval goes to the next higher level.

If it says “The rules cannot fill this case completely”, then, for example, a superior, a currency rate or enough available people are missing. You can still continue and complete the workflow in the Workflow step; sending then needs a reason.

If your administration has switched on AI help for the signing authority rules, Read from document is shown at the top. The AI reads the request type, amount and counterparty from the first PDF document and enters them. It only proposes values it is unsure about (“Found in the document: …”); with Use it you enter them. It cannot read a scanned document without readable text.

In the Workflow step, the Workflow from the signing authority rules box is shown above the tasks.

  • If the workflow follows the rules, it says “The workflow follows the signing authority rules.”
  • You may change the workflow. Adding further people is not a deviation. But if you leave out a required person, give them a weaker signature or put them before a step that comes first according to the rules, actaSIGN lists this under “The workflow deviates from the signing authority rules”.
  • With a deviation, the Reason field is required. Without a reason you cannot continue, and actaSIGN also refuses to send.
  • Use the proposal again resets the workflow to the proposal. Continue without the rules detaches the request from the rules; it is then not checked against them.

If you change the request type or a value in the Subject & Settings step, actaSIGN works out the proposal again.

If you start with a template or from scratch and choose a request type the rules know, the Workflow step shows Signing authority rules available. Check against the rules compares your workflow with the rules; Take over the proposal replaces it with the proposal. Documents, fields and texts stay.

  • When you send, actaSIGN works it out once more with the version that applies then, and compares it with your workflow.
  • A deviation is recorded with your reason. The administration approves or rejects it afterwards; the request continues in both cases.
  • The request’s protocol contains a Signing authority rules section with the version, request type, amount that counts, intended people, result and, if applicable, the reason.
  • If a task stays open longer than the escalation period of the rules, you get a notice once saying who may take over according to the rules. Nothing is forwarded automatically.
  • If a person is away, their task only goes to the deputy if the amount is below the deputy’s limit and the role may be stood in for.
  • The details of the request become data of the request. You can change them in the Subject & Settings step and use them, e.g., in messages.
  • If you then switch to a process or form template, the request is no longer linked to the rules.